01/05/13

Insects and other foods the trout
should be eating:
Hatching:
1.    BWOs (Little BWOs)
2.    Midges
3.    Little Winter Stonefliesl

Most available/ Other types of food:
4.    Sculpin, Minnows (Streamers)



Fly Fishing School - A Huge Basic Casting Mistake
Nine out of ten beginners, and a few that have been fishing a good while, that I watch casting flies on the
streams of Great Smoky Mountains National Park make straight-line cast. By that, I mean their fly line, leader
and tippet lands on the water in a straight line.
That may be fine for showing someone how far you can
cast or okay is your fishing a streamer, but if your doing that fishing a dry fly or small nymph, you
haven't finished the first grade of fly fishing.

Unless that type of cast is made directly upstream, meaning not the slightest bit to the left or right of the exact
opposite direction the current is flowing, it will cause instant drag. If it does land such that your fly drifts
directly back down stream in line with the current,  you fly will be passing directly over the same line or water
that you fly line, leader and tippet just passed over. In other words, it a trout was positioned downstream of
where you fly landed, your leader and fly line would spook the trout before the fish had a chance to see your
fly. This is called, lining the fish.

If the fly line lands slightly across the current, the resistance of the fly line on the water is greater than that on
the tippet and fly, and your fly line in essence "pulls" the fly downstream, which of course, causes the fly to
drag. The fly will instantly begin to travel faster than the water is flowing and it will leave a tiny wake on the
surface that trout can instantly detect is unnatural.

Ever real insect that trout normally see on the surface of the water is floating at the same speed of the water.
Leaves, twigs, insects and other floating items don't drag on the surface. When they do, the unnatural
disturbance tends to scare the trout more than attract them. If your fly doesn't drift drag-free, it will tend to
scare trout more than it will tend to fool into taking it for an insect.

Most of the time, the anglers I see making this very common mistake, meaning they make an upstream cast
that straightens out their fly line, leader and tippet such that it lands on the water in a straight line, mend their
line as soon as they see the fly begin to drag. The problem with this is mending the fly line on the surface of
the water causes additional disturbance that may spook the trout downstream of your fly.
In other words my
friends, any time your mending you line on the water, your attempting to correct a mistake. Your
trying to fix a problem you made with your cast.
I'm not saying there is never a time that mending your
fly line isn't necessary. I am saying mending your fly line tends to spook trout when in many, if not  most
cases, it isn't necessary.

I'll make this as plain and simple as I can. When you are fishing the small, pocket water streams of the
Smokies, making upstream presentations like you most often should be doing,
you should be making
"crooked" cast, not cast that straighten out your fly line, leader and tippet.
These types of cast are
called
reach cast, curve cast and even in the air mends. I prefer reach cast because they are easy to
make and in most cases, all that is necessary. Curve cast are more for getting your fly to land in a place an
obstruction is preventing you from making a straight-line cast. Just for example, you may want your fly to land
behind a rock when a straight line presentation would put your leader or fly line directly over the rock. Curve
cast are also far more difficult to perfect than a reach cast.

When you make a reach cast, your fly and tippet, and in some cases part or all of the leader itself, lands to
your left or right of the fly line. The fly line, and maybe a portion of the leader lands in a straight line across
the water, but the tippet and a part or all of the leader lands from a few inches to a few feet, left or right of the
fly line. This keeps your fly line well away from your target where you want the fly to drift.
It just as
importantly allows the fly to drift drag fee because of the slack in the leader and tippet.

To make a reach cast, you simple cast as you normally would but you move your fly line to the right or left or
the target. While the fly line is unrolling, you reach or extend your arm and tip of the fly rod out to the right or
left, away from the target. This will put an "in-the-air curve" or mend, whichever you prefer to call it, in the
leader and tippet during the time the fly line is unrolling,
before it lands on the water.. Depending on exactly
when you "reach", you can put a small curve or bend in just the tippet, or a big curve or bend in the tippet
and leader. In other words, you can make the fly land above your target like it should, and the fly line land a
few inches, or a few feet, to the left or right of your target.
It gets the fly line out of the view of the trout
and at the same time, prevents your fly from dragging.

When you see someone mending the heck out of their fly line, you are looking at someone who doesn't know
how to cast to trout.

When you see someone that's not getting a drag free drift, you are looking at someone who doesn't know
how to cast to trout.

Learn to make crooked cast and you will improve you success considerably. It is actually very easy to learn to
do.
Copyright 2013 James Marsh
New Schedule of Daily Articles
Mondays: Weather and Stream Condition
Forecast - Coming Week
Tuesdays: Fly Fishing Strategies - Which
Flies To Use - Coming Week
Wednesday: Fish Tales
Thursday: Smoky Mountains Fishing Report
Friday: Getting Started
Saturday: Fly Fishing School
Sunday: This Week's Featured Trout Food